D102I资料

D100ISeries

High IsolationMiniature, 1W SIPDC/DC Con vert ers

Electrical Specifi cations

Specifi cations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice.

Key Features:

• 1W Output Power• Miniature SIP Case• 3,000 VDC Isolation• Single & Dual Outputs• Complies to RFI Standards• >1.12 MHour MTBF• 36 Standard Models

• Industry Standard Pin-Out

InputParameterMin.5 VDC Input4.512 VDC Input10.824 VDC Input21.648 VDC Input43.2Internal Capacitor12 μH Source InductanceConditionsMin.ConditionsTyp.5.012.024.048.020Max.Max.5.513.226.452.8UnitsInput Voltage RangeVDCInput FilterRefl ected Ripple CurrentmA P - PUnits%%%mV P - P%%/ºCOutputParameterOutput Voltage AccuracyOutput Voltage BalanceLine RegulationLoad Regulation (Note 1)Ripple & Noise (20 MHz) (Note 2)Output Power ProtectionTemperature Coeffi cientOutput Short CircuitTyp.±3.0Dual Output , Balanced Loads±1.0For Vin Change of 1%±1.2See Model Selection Guide75110Momentary (0.5 Sec.)Units60 SecondsVDC500 VDCMΩ100 kHz, 1V60pF80kHzEN55022 B, EN55024 B, IEC 61000-4-2, IEC 61000-4-3, FCC 47 CFR Part 15 BConditionsAmbientCaseMin.-40Typ.+25Max.+85+100+12595UnitsºCºCºC%ConditionsMin.3,0001,000Typ.Max.±0.02RoHS Compliant

GeneralParameterIsolation VoltageIsolation ResistanceIsolation CapacitanceSwitching FrequencyEMI/RFIEnvironmentalParameterOperating Temperature RangeOperating Temperature RangeStorage Temperature RangeCoolingHumidity-40Free Air ConvectionRH, Non-condensingMicroPower DirectPhysical292 Page StreetSuite D

Stoughton, MA 02072USA

T: (781) 344-8226F: (781) 344-8481

E: sales@micropowerdirect.comW: www.micropowerdirect.com

Case Size (5V 12V & 24V Input Models)Case Size (48V Input Models)Case MaterialWeight 0.76 x 0.24 x 0.39 Inches (19.5 x 6.0 x 10.0 mm)0.76 x 0.28 x 0.39 Inches (19.5 x 7.2 x 10.0 mm)Non-Conductive Black Plastic (UL94-V0)0.08 Oz (2.3g)ConditionsMIL HDBK 217F, 25ºC, Gnd BenignConditions5 VDC Input12 VDC Input24 VDC Input48 VDC Input1.5 mm From Case For 10 SecAll ModelsMin.1.12Min.-0.7-0.7-0.7-0.7Typ.Max.UnitsMHoursUnitsReliability Specifi cationsParameterMTBFAbsolute Maximum RatingsParameterTyp.Max.7.015.028.054.0260450Input Voltage Surge (1 Sec)VDCLead TemperatureInternal Power DissipationºCmWCaution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.元器件交易网www.cecb2b.com

Model Selection Guide

ModelNumberD101ID102ID103ID104ID105ID106ID107ID108ID109ID111ID112ID113ID114ID115ID116ID117ID118ID119ID121ID122ID123ID124ID125ID126ID127ID128ID129ID131ID132ID133ID134ID135ID136ID137ID138ID139IInputOutputLoadVoltage (VDC)Current (mA)RegulationVoltageCurrentCurrentNominalRangeFull-LoadNo-Load(VDC)(mA, Max)(mA, Min)(%, Max) 54.5 - 5.5267303.3303.06.01054.5 - 5.5256305.0200.04.01054.5 - 5.5267309.0111.02.21054.5 - 5.52633012.083.31.61054.5 - 5.52633015.066.61.31054.5 - 5.527030±5.0±100.0±2.01054.5 - 5.525630±9.0±55.5±1.11054.5 - 5.525630±12.0±41.6±0.81054.5 - 5.525030±15.0±33.3±0.6101210.8 - 13.2113203.3303.06.0101210.8 - 13.2113205.0200.04.0101210.8 - 13.2111209.0111.02.2101210.8 - 13.21082012.083.31.6101210.8 - 13.21062015.066.61.3101210.8 - 13.211120±5.0±100.0±2.0101210.8 - 13.210920±9.0±55.5±1.1101210.8 - 13.210620±12.0±41.6±0.8101210.8 - 13.210420±15.0±33.3±0.6102421.6 - 26.456103.3303.06.0102421.6 - 26.454105.0200.04.0102421.6 - 26.456109.0111.02.2102421.6 - 26.4531012.083.31.6102421.6 - 26.4531015.066.61.3102421.6 - 26.45610±5.0±100.0±2.0102421.6 - 26.45410±9.0±55.5±1.1102421.6 - 26.45310±12.0±41.6±0.8102421.6 - 26.45310±15.0±33.3±0.6104843.2 - 52.82963.3303.06.0104843.2 - 52.82965.0200.04.0104843.2 - 52.82869.0111.02.2104843.2 - 52.828612.083.31.6104843.2 - 52.828615.066.61.3104843.2 - 52.8306±5.0±100.0±2.0104843.2 - 52.8296±9.0±55.5±1.1104843.2 - 52.8286±12.0±41.6±0.8104843.2 - 52.8286±15.0±33.3±0.610Other input/output combinations are available(i.e. 24.0 VDC). Contact the factory for details at:

sales@micropowerdirect.com

Notes:

1. Output load regulation is specifi ed for a load change of 20% to 100%.

2. These units do not require external components to operate, but the use of an input capacitor (10 μF) may enhance performance in some applications. It is recommended that an input capacitor of 4.7 uF to 47 uF (dependent upon the application) be used on 48V input model.

An output capacitor (4.7 μF to 100 μF or ±4.7 μF to ±68 μF) may be used to reduce ripple. To improve EMI performance, a simple fi lter network consisting of a 10 uF to 100 uF capacitor and 12 uH inductor should be effective.

3. These units will operate at no load without damage, but may not meet all specifi cations.4. Dual output units may be connected to provide a 10V, 18V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and fl oat the output common.

5. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating.

Effi ciency(%, Typ)757875767674787880747475777875767880757775787874767878727274747570727474Dual+Vin-Vin-VoutFuse RatingSlow-Blow(mA)500500500500500500500500500200200200200200200200200200100100100100100100100100100100100100100100100100100100Pin67SingleNo Pin+VoutDualCommon+VoutPin ConnectionsPin125Single+Vin-Vin-VoutMechanical DimensionsDerating Curve

Capacitive LoadSingle Output(μF Max)220Dual Output(μF Max)±100MicroPower Direct

www.micropowerdirect.com

Notes:

• All dimensions are typical in inches (mm)All dimens

• Tolerance x.xx = Tolerance x±0.01 (±0.25)

• Pin 1 is marked by a “dot” or indentation onPin 1 is mar

the side of the unit the side of

292 Page Street, STE D, Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com